How’s business? If its good or bad you may want to consider buying this add on for Vectorworks. If you are busy then it will save you time and if business is not so good then it might just give you an edge on the competition and help you get more work. First a disclaimer: I got my copy free so that I could write this review.
Advertisement
Every real, as opposed to virtual I guess, project that we architects do has a site. The site might be an empty field or an infill one with existing buildings all around. It could also be an existing building with work done on the outside or even the inside. These days many of us are designing in 3D creating nifty little 3D models of our work that often just float around in space with no reference to the actual site. Or we may create the site and its surroundings virtually to have a place to put the model. But for the client and for the completion of the design process what could be more illustrative than to see the new structure on a photo of the actual site.
This can be done using Vectorworks importing a picture and then matching the exact angle and perspective of the picture with a 3D view of the Vectorworks model. It’s not too difficult if we know the exact position of the camera, the angle, the focal length, et cetera, of the imported picture. But I can tell you from my own experience that what might not seem too difficult can take hours of messing around and trial and error to get a result that even seems close to reality. This is assuming you know the details of the imported photo mentioned above, but what if the client just hands you a picture taken from some random location?
Cameramatch
Cameramatch solves all of these problems and once one learns how to use the program the “photo” of the site combined with the model of the proposed project can be accomplished in minutes using just about any random photo–not hours. Time savings on just one of these should more than pay for the 100.USD cost of the program and from then on it’s just more money in your pocket.
Now I have to admit that I have had a few start-up issues. The instructions, who wants to read instructions, are detailed and one must read them and follow them. One must also be familiar with the base program, which in this case is the latest Vectorworks 2011, by Nemetschek Vectorworks, Inc.. Cameramatch is also available for earlier versions. I have been at fault in both cases. I just got the new version of Vectorworks and I don’t really like following instructions. I know I’m not alone otherwise they wouldn’t have a ‘quickstart’ guide in just about everything we buy these days.
Here are before and after photos of a little house we are working on in the Czech Republic. It’s actually a teardown and rebuild of an existing structure attached to another house. The photo used was taken at random by the client. We have not even been to the site.
Cameramatch works by aligning a 3D view of a model in Vectorworks to a photo’s specific perspective. The general idea is you are going to model something in Vectorworks from the vantage point of a specific photo, whether you re-use that photo as part of your final visualization product or not.
In the top image below we start with the basic establishing of 3D reference points in the photo taken. (see image 01). In the second photo below you “align” your 3D model created in Vectorworks (or possibly created in another program and brought into Vectorworks) to the Camermatch object in the annotation space of the viewport. (see image 02).
01 – Cameramatch 2011. Locations of dots and lines indicate found perspective guides for the model.
02 – Cameramatch 2011’s process and interface. The 3D model aligns with guides established through the Cameramatch object.
This was just my second attempt at using the program; so don’t think that it’s the best that can be done with the program. Go to the site www.panzercad.com and look for some examples done by others to get a better idea of the true potential of the program. And after we make some revisions to this design requested by the client I will make a better version of this one.
The program, like Vectorworks which it runs in, is available for both the Mac and the PC. As with all the latest versions of most software, the more computer power you have the more smoothly the program will work. Cameramatch and Vectorworks are no exceptions, they both seem to like my new laptop using Windows 7 with lots of RAM a lot better than my older XP PC. But I am able to get the same results with both computers; it just takes longer on the old one and it gets a bit fussy when it starts to run out of RAM.
03 – Cameramatch 2011 – The final planned architectural model.
As you can see from the final image above (image 03) the results of Cameramatch in helping to create 3D models based on, and coordinated with, photography is very good. I close with a quote from Cameramatch creator Matt Panzer and suggest that if you really want to get a good idea of what the program does visit his website. You can also download a free trial version here.
“Some CM (Cameramatch) users have made CM part of their normal workflow for every project. The clients love it because they immediately understand how the design fits into the existing structure or site. And early stages of the project benefit since the designer only needs to model the proposed parts in detail.” — Matt Panzer.
Pros: Simple and clear plugin user interface within Vectorworks; all new calculation engine works much better with particular perspective views; suggested sheet layer DPI listed on Object Info Palette; scales with Viewport scale changes; new shadow object eliminates need to use external image editor for simple shadows over the image; many smaller new features and changes
Cons: Instructions do require a thorough read-up but this is not a significant issue in itself; no significant performance issues on recent and modern hardware on both platforms; no major issues.
Advice: For those wishing to save days and hours on setting up 3D models–in Vectorworks–from site photography of existing conditions and context Cameramatch 2011 is a must-have plugin application.
Cost: 100.USD. Cameramatch 2011 requires Vectorworks 2011. For earlier versions of Vectorworks there are available earlier versions of Cameramatch. To learn more visit them online here: www.panzercad.com
To learn more about our contributor, John Helm, NCARB visit here. To see other Architosh product reviews published prior to our new site, please visit this old Features page. We have an array of indepth product reviews across CAD and 3D industry spectrums.
SaveSave